The first diagnostic trouble code or no fault detected will be indicated by the on-board diagnostic lamp. When the check engine light comes Hyundai Getz P1693 code on the first you should check is the gas cap. The improper timing of the explosion sometimes pushes the cylinder the wrong direction or interferes with the turning of the crank. Enter the 5 character trouble codes in the search box and submit the search. In a properly timed engine, this explosion occurs at the proper moment to send the piston to the bottom of the cylinder and provide power to the drive shaft. I have no Check engine Light coming on, and the Battery has been checked and fine I am leaning towards it being the Immobiliser. If system is in normal condition, pointer of voltmeter indicates a normal pattern.
. The data are a string of 9 bytes defined by vehicle manufacturer. Is the chip inside and where would i get a replacement chip and approx. Yes the P1693 is a companion code and has no really meaning but. But if Istart from the zero position on the starter it doesn't start on the first try.
I hit my door unlock on mt Key fab and the doors unlocked fromt here I proceeded start my car. If you've already made it to the store, you might as well just replace it. If codes other than these are indicated, repeat self-diagnosis. Unlike the cheaper Haynes and Chilton manuals that cover multiple year models, leaving the exact information you need to fix your car, these professional manuals cover your exact year, make, model. The solution is here : Hyundai Getz P1693 Possible Solution : Disconnected, dirty or fouled spark plugs are common causes for engines that won't start. Pull over, retighten it, and take a look at the cap to see if it has any cracks in it.
We have 2 keys one for me and one for my wife but they don't have buttons on it. Any Advise appriciated Kiwalian O. The car is going into the mechanic on Friday to replace the timing belt. If that immobiliser light is not on, the engine will not start. If you want to see a video of this and how to properly do it please reffer to my web site and watch the video I produced so you can give us acurrate information on your problems your having with your truck. Anyone else had these errors and what exactly was the fault Thanks Kiwalian For general application when a Getz is either intermittent or simply won't start.
The sensors have been replaced, fuel caps, intake manifold gaskets, computers replaced, etc. As worded by my Cummins certified friend. I would return it to the installer www. If your Check engine light is on you may have a serious problem. The write procedure is unique; therefore the content of transponder can never be modified or changed. If your are for a different car, select that vehicle series before searching for the diagnostic codes because not all used by one manufacture are used by the other makes. If a test is to made during cranking, the power to cigarette lighter will be interrupted therefore, use a separate battery harness for multi-use tester.
All you need to do is take the old one off and screw on the new one. Then tighten the torx screws. Hello, I am hoping for a little help. In the V-engine design, Ford follows a similar design with the number one cylinder at the front left of the engine. If your spark plugs look good, problems with your ignition system can also preventing a spark. We are not responsible for any actions you take on your vehicle.
So if you get this P1693 code, first check to make sure you're getting a good 5 volt reference signal at the sensor. The currently selected is for the Hyundai makes. So you should chech it on our car models. In the V-6 configuration, cylinder 4 is at the front right of the engine and in a V-8, cylinder number 5 is in that location. My lights flash when I lock it, but the horn doesn't sound. As an example, one flash, followed by a 2 second pause, followed by two flashes and another 2 second pause, followed by two flashes and a 2 second pause, followed by three flashes and another 2 second pause, indicates a failure code 1223. So many of these cars have the same problem.
©, 2016 Rick Muscoplat eautorepair. In the case of a broken wire, the sensor never sees the voltage and the computer assumes a major fault. While not car-threatening, it's good to take care of this right away to improve gas mileage. Now don't ask yourself; What should you do with P1693 code? I have a 2003 Getz 3 Door 1. The vehicle service manual should be consulted for more information on possible causes of the fault, along with required testing. The fault code will be repeated until the No. Autozone is one place that will give you the code number.
Then even in rare cases seeing the P1693 code in both computers pointing out that both computers have codes. So you have to refer to the factory legends to learn the identification symbols and then refer back to circuit diagrams to find the splice and ground locations. The problem is caused by the variable cylinder management system switching on and off during light throttle conditions, at cruising speeds, or when driving on flat roads. The list of automotive Makes at the right edge of the screen. The vehicle service manual should be consulted for more information on possible causes of the fault, along with required testing. Only the results from the encryption algorithm are transferred. Look up the other , please use the search box.
If you need to dig into your doors, dash or console, Alldatadiy. It is almost impossible to calculate the vehicle specific data from the encryption result. Other manufacturers sometimes use an alternating pattern in the V-engines. The data are a string of 9 bytes defined by vehicle manufacturer. If any abnormality is in the memory, pointer of voltmeter will deflect indicating an abnormal condition. However, also includes disassembly instructions for interior trim panels and exterior items like headlights and tail lights. The vehicle specific data are written into the transponder memory.