Oil quantity: Total amount: 2. Fill the engine with sufficient oil to reach the specified level. Use a trough or a similar object as shown to prevent coolant from spilling on the foot- rest. Install the front carrier by installing the bolts and tightening them to the specified torques. Adjust the spring preload as follows. Move in direction a to turn on the starter choke. Never climb hills with excessively slippery or loose surfaces.
Carefully choose your path and sible. Use only the designated quality brake flu- id. In ad- dition, the final gear oil must be changed as follows at the intervals specified in the periodic mainte- nance and lubrication chart. The chart below is printed only as a reminder to you that the maintenance work is required. If the cables do not operate smoothly, ask a Yamaha dealer to replace them.
Do not shift from drive position low-range to Shift to the park position and follow the instruction high-range or vice versa without coming to a on page 6-1 to start the engine. Grizzly Sunken Part 2 Image info : Resolution:1280x720 Size:69kB 16. Thought it was the carb. Refer to this section each time a panel needs to be removed and installed. I plan on using the search functions as well.
Never attempt to operate over large obstacles, such as large rocks or fallen trees. I have looked around but there is limited info or pictures on what I would need to buy or where it even mounts. Remove the coolant reservoir cap. Automotive type wax may be applied to ing. Insert a new headlight bulb into the bulb hold- it in and turning it counterclockwise. This may overload the circuit and cause the fuse to 1. Could cause carbon monoxide poisoning, possibly leading to death.
Turn the brake lever free play adjusting bolt in. After draining the coolant, thoroughly 6. Check the coolant level in the coolant then add coolant or distilled water to raise reservoir when the engine is cold as the it to the specified level. Coolant reservoir cap If water has been added to the coolant, have 2. Wheel nut torque: Front: 55 Nm 5. An oil filter wrench is available at a nearby Yamaha dealer.
It is a bear to pull start, never had. You could be se- verely burned by the sulfuric acid in battery electrolyte. Pull it toward the handlebar to ap- ply the front brake. Turn the adjusting bolt until the throttle le- ver free play is 3—5 mm 0. Brake lever free play Yamaha dealer adjust it. Learn to safely control skidding or sliding by prac- ticing at low speeds and on level, smooth terrain. Follow the same procedure as for starting a cold 7.
Be sure to keep your feet firmly mounted on the footboards at all times. See pages 8-6—8-7 for panel removal and installation proce- dures. Ignition system is Spark is good. It should be cleaned and lubri- foam air filter oil is not available, motor oil may be used. A downloadable Yamaha Grizzly repair manual is a digitally delivered book of repair instructions for learning how to service, maintain, troubleshoot and overhaul the complete off-road all-terrine vehicle. However, the spark plug should be tightened to the specified torque as soon as possible. If oil is leaking, check for the cause.
But we traced the issues to the starter and replaced it. If the fuel tank is overfilled, fuel could spill out due to heat from the engine or the sun. Always be careful when skidding or sliding. Original owner traded it in on a new side-by-side. They should then ry or death of the child. Rear shock absorber spring 15.
Check the differential gear case for oil leak- age. Differential gear oil filler bolt: 23 Nm 2. Bolt stall the quick fasteners. Ride cautiously in unfamiliar areas. Lubricate the inner cables and the cable ends. It contains important safety information. Main switch The engine can be started only at this position and the headlights and taillight come on when the light switch is on.
V-belt cooling duct check hose Left side 1. If you stall or Always be sure there are no obstacles or people roll backwards, follow the special procedure for behind you when you operate in reverse. If this should happen, remove the battery and recharge it. Al- hills as described in this manual. What's the difference and how do they all work together. Never use a material in place of the proper fuse. To reduce the tendency for the front wheels to slide in loose or slippery conditions, positioning your weight over the front wheels will sometimes help.